Step 2: Jack stand placement. Place the jack stands at the appropriate points to support the vehicle in the lowest setting possible for safety and stability. Slowly lower the vehicle onto the jack stands. Once lowered, leave the jack in place for safety. Step 1: Remove the oil filter. With the drain pan in place to catch the oil, use the oil filter wrench to remove the oil filter.
Step 2: Remove the drain plug. Once the oil filter is removed, move the drain pan underneath the oil pan. Remove the oil drain plug and allow several minutes for the oil to drain into the pan. Dispose of the oil and filter properly. Step 1: Select the appropriate socket and ratchet. Use an extension if needed. Sometimes the pan will just fall loose. Others, you may need to gently tap or pry the pan away from the engine block.
Once the pan is loosened, remove the 4 remaining oil pan bolts. Remove the pan carefully as to not damage the oil pick up located within the oil pan. Step 2: Clean up. Also, clean the oil pan inside and out. Step 1: Remove the old gasket material. Using the scraper, gently remove any gasket material on the oil pan as well as the engine block mounting surface. Wipe both the pan and engine mounting surfaces clean and let dry.
Step 2: Install the pan gasket. Following the directions on the rtv package, apply a thin film of rtv to the oil pan mounting surface. Allow the rtv to set up for a few minutes. Once the rtv has set, apply the pan gasket to the surface, applying even pressure all around. Step 3: Install the pan. Insert all the oil pan bolts hand tight to start. To avoid distorting the oil pan and future leaks, torque the oil pan bolts to manufacturer's specifications. If you do not have a repair manual for your vehicle, your local auto parts store should be able to provide the specifications for you.
Step 1: Add engine oil. Reinstall the oil pan drain plug and new oil filter. Fill the engine with the recommend oil. Check for any obvious leaks before lowering the vehicle. Step 2: Check for leaks. Remove the jack stands and lower the vehicle. Start the vehicle and let it run for a minute or so. Turn the engine off. Wait a few minutes and check the oil level. Top off if needed.
Once checked, start the vehicle and let it warm up at idle. Check for any leaks after warmed up and again after the vehicle has been driven.
If you see oil on the ground underneath the front of your car and suspect a leaking oil pan gasket , contact YourMechanic today to schedule a visit from one of our mobile technicians today. The most popular service booked by readers of this article is Oil Pan Gasket Replacement. Check your oil often to ensure oil levels are normal as low oil levels are a clear indication that something is wrong.
Running your engine without the proper amount of oil can lead to major engine damages. Any time your engine shows signs of difficulty, be sure to take your car to a trusted automotive professional. Allowing your engine to smoke as a result of a leak, can cause additional damages to oxygen sensors and other components from being saturated by oil which can cause sensors, gaskets, and other vital components to fail.
Further, overheating engines can cause serious and permanent damage to the engine that may lead to replacement or extensive repairs. Enter your email address and we'll email you a digital version of this coupon that you can present on your mobile device at your Sun Devil Auto Shop.
Skip to content. Find a Location Locations. Make An Appointment Appointments. What is a Gasket? Types of Gaskets Your vehicle is equipped with a few gaskets including the head gasket and valve gasket.
Oil Pan Gasket Leak Symptoms With use and wear, after some time the oil pan gasket will begin to fail. You may also notice: Low Oil Level — Oil leaks are often difficult to locate, making a leak from the oil pan gasket almost impossible to find.
A lower than usual oil level is a sure sign that there is an oil leak. Overheating — Along with coolant, motor oil helps keep the engine cool by reducing friction and heat. If oil levels have dropped, the engine will have difficulty preventing heat produced by friction, resulting in an overheated engine. Step 4: A service manual helps identify all oil-pan bolt locations. Some might be obscured behind other parts.
Step 5: Removing the wheel-well-liner pieces eased access to the outboard passenger's side bolts on this vehicle. Step 6: Once all bolts are removed, the pan can be dropped. If necessary, tap it lightly with a mallet to break the seal. Step 7: Scrape off any gasket residue and clean all sealing surfaces thoroughly with a solvent. Also clean the inside of the oil pan and inspect it for cracks. Then install the new gasket per its instructions.
This one uses regular grease to hold it in position. Step 8: Use thread sealer, if specified, then torque the oil pan bolts to spec in a spiral pattern, beginning in the center. Reattach any accessory brackets, refill the crankcase with oil, start the engine and inspect for leaks.
0コメント